Hi sewing friends! Is the summer in UK already over??? That cannot be!!! I haven’t had a chance to wear my new dress that I made especially for a hot summer days!!! Couple of weeks ago I posted on my Instagram Stories 3 different yet very similar summer dresses that I was considering making, but suddenly changed my mind when I realized the total cost of the patterns and all fabrics I would need! (Are you rolling your eyes too??) Anyway, money problems aside I wanted to improve my pattern drafting/hacking skills so I grabbed my beloved Ogden Cami pattern, traced it on a clean paper and begin my hacking process. The result makes me smile every time I look at it!


Inspiration
Photo: Individual pattern covers.
Seren dress by Tilly and the Buttons was the very first dress that I really wanted to make. I was not that keen about these ruffles but the button placket was major envy driven force that made me want to do this project.
My eyes nearly popped out when I came across the Fiona sundress by Closet Case Patterns. This dress is slightly more fitted but looking at it I knew I wanted a bodice with princess seams.
Jessica dress by Mimi G is the closest reflection of what I wanted to achieve. Gathered skirt and big patch pockets were a must feature that I wanted to recreate.
Hacking the pattern
If you are also on a buying fabric/pattern ban feel free to use this tutorial.
First trace front and back Ogden Cami pattern pieces up to your waistline. For me this is about an inch below the shorten and lengthen line but remember I’m pretty short. Before you do anything else measure your waistline and the waistline on the pattern. The difference between those measurement will be need later.
Draw a vertical line starting in the middle of strap placement ensuring it runs parallel to center front and back. From now on this will be our grain line.
On the back pattern piece extend the line (slightly curved) that starts at your armpit ending at a center. It need to finish at 90 degree angle here.


Cut along the lines .

You can mark those pieces B1 and B2 so you won’t get confused. The top piece will be needed later so put it aside for now.
Your B1 pattern is cut on fold so make sure to mark it. This is a centre back piece that will be elasticated so add about 3.5 cm at the side ( that includes seam allowance). You will need to cut two on fold ( one main bodice and one lining).

On B2 piece add seam allowance to the side you cut out before.

At this point you will need the difference in waistline measurements. For me it was about 16 cm. As the bodice needs to be more fitted around the waist draw a straight line at the side seam, parallel to grain line and cut it off. This takes away about 6 cm from a total waist circumference.

Now we will work on the from bodice piece. Draw a straight line and the side seam in the same way as before (this again reduces waist circumference by another 6 cm). Next cut along the first line dividing the front pattern piece in two F1 and F2.
So far we managed to reduce the waist by 12 cm in total. The remaining 4 cm will be taken away at the next stage. Mark 2 cm from a cut grain line on both pieces.

Now we will do some shaping to the princess seam so add some extra paper.

In the process of reducing the excess fabric at the waist we also amended bust circumstance, which we will need to reverse. I drew some horizontal lines to make this step a little easier to navigate.
Measure in few places the amount you had taken away at the side seam, divide it in half and mark it as a dots on both F1 and F2 pattern pieces at the cut grain line. Now draw a curved line starting at the top where the strap placement is and ending at the waist at marked 2 cm. Do not worry if you do not go through all your dots.

I will be using buttons 2cm in diameter, so decided that my button placket will be 3.5cm wide.
Not to bore you with calculation, cut off 0.75cm at the centre front on piece F2.

Extend the strap pattern by 13,5 cm or whatever your measurement is.

At this stage I wanted to test the fit of the bodice so a used some old fabric and cut out my new front and back bodice pieces, straps and two rectangles 9cm by 30 cm ( short button placket) and a long roughly gathered piece and made a muslin.
What I learnt is that because Ogden Cami pattern has no bust shaping the front waistline is raising substantially in comparison to my back.

Going back to the front bodice pattern pieces I cut along the horizontal lines leaving a hinges at the side seam on F1 and opened it by a total of about 5/6 cm. On F2 I spread the distance equally. The amount needed will depend on your bust cap size, so I would advise you to make a test bodice.
Other then that I adjusted the princess lines slightly taking it in above and below the bust making it more fitted.

To draft a skirt part of your dress measure the length from your waistline to a desired skirt hem line, draw a vertical line and square it off on both ends…
Again it is up to you how much and where you want the gathering on the skirt but I opted to only partiality gather my skirt at seams F1 and F2, B1 and B2. I was considering to do pleats instead, hence the P1,P2,P3 markings….so ignore it.
I added 12 cm between F1 and F2 , and 8cm between B1 and B2.


Square of the skirt side seam on both back and front. Back piece will be cut on fold once. Front piece will be cut twice.
I wanted more of an A-line skirt so added extra 5 cm at the hem to both front and back.

Place the side seam together and smooth the hem and waist lines.


Now you can draft a button placket pattern, which is 9cm wide by total length of F2 and front skirt (1cm seam allowance included).
For patch pockets I drew a square 20cm by 20cm adding extra 2 cm to the top.


If you are still reading this congratulations!!! You completed the entire hacking/drafting process. Hope I didn’t bore you too much. Hihihihi
In the next post I will talk more about sewing process, my fabric choice and anything else worth of knowing.
~See you next Sunday~
Monika xxx
Pingback: Summary of 2019 and plans for 2020 – Allsewpetite